ZEDEX® 410 family
The most precise – up to 180 °C
ZX-410® is a material with excellent technical properties and an extremely favorable price/performance ratio. ZX-410® has the 2nd best PV-value at 10m/min-after ZX-750V5T®– and the highest long-term compressive strength (10’000h) of a unreinforced polymer among the ZEDEX® materials.
The E-modulus is pretty constant up to 180°C and its CTE is low. The modification ZX-410V7T® has practically the same aluminium’s CTE allowing e.g. a constant clearance in applications with a smart design. Its low toxicity of combustion gases makes it suitable also for environments with high safety requirements.
When to use the family ZX-410® ?
- With high temperature fluctuations
(for this modification ZX-410V7T® optimal) - At very high surface pressures
- At high pv values at medium speeds
When is the ZX-410® family not suitable?
- If low water absorption is required (e.g. the family ZX-530® as alternative)
- Low fatigue strength (e.g. the family ZX-324® as alternative)
- If very little wear and friction is required
(e.g. ZX-410VMT® as alternative)
What can be replaced?
ZEDEX | temperature | strength | toughness | friction | precision | wear | costs | pv values | Chemicals | |||
ZX-410 | 6 | 6 | 4 | 6 | 9 | 7 | 4 | 10 | 5 | |||
ZX-410V7T | 6 | 7 | 2 | 6 | 10 | 9 | 4 | 8 | 6 | |||
Standard materials | Replacement for | |||||||||||
PEEK | 8 | 6 | 7 | 5 | 7 | 4 | 4 | 7 | 8 | |||
PEI | 5 | 6 | 10 | 5 | 8 | 3 | 6 | 3 | 4 | |||
PA12 | 3 | 3 | 10 | 6 | 3 | 4 | 9 | 4 | 3 | |||
PA 4.6 | 4 | 7 | 8 | 3 | 2 | 4 | 9 | 5 | 3 | |||
PPS | 5 | 7 | 2 | 6 | 8 | 2 | 6 | 3 | 9 | |||
TPI | 7 | 6 | 7 | 5 | 7 | 4 | 3 | 7 | 7 |
Basic type
ZX-410
⟶ value the higher = better
ZX-410 Material data sheet
Characteristics
- up to 180 °C hard, stiff, tough
- mechanical properties, wear and PV-value better than the
PEEK´s ones - high dimensional stability
- high chemical resistance
- high hydrolysis resistance, except with basic substances
- very high UV and y radiation resistance
- flame resistant (low toxicity of flue gases)
- resistance to stress cracking
- good machinability
- cheaper than PEEK
Resistance
- UV-radiation: (1000 hours Xenon DIN 53597)
tensile strength: –43 % - Gamma-radiation: limit absorbed dose 9000 kGy
- Chemicals, resistant: mineral acids, salt solutions,
aqueous alkali pH< 9, alcohols, ethers, sulfuric acid 50 % - Chemicals, not resistant: ketones, chloroform, MEK, ethylacetate, methylene dichloride, trichloroethane, hydraulic oil, dichloromethane
- Lubricants and fuels: limited resistance
- Water: max. water absorption: 0,6 %, dimensional changes: 0,25 %, up to 125 °C resistant
- Fire behaviour: oxygen index (LOI): 47 %, classification: V-0 (UL94), low flue gas emission
Operational parameters
- Temperature (T):
-70°C to +180°C (+200°C) - Surface pressure (p):
max. 48 (142) MPa - Sliding speed (v)
max. 100 m/min - Fatigue(S)
tensile fatique strength at 20 °C and and 106 stress cycles,
1 Hz = 33 MPaImpacts, vibrations, edge loading, gamma rays in hot and cold water.
Available as:
- plastic granules
- rods
- tubes
- sheets
- 3D Tribo Filament
- machined components
- injection moulded parts
- plain bearing bushes according to DIN
Modification
ZX-410VMT
⟶ value the higher = better
ZX-410VMT Material data sheet
Fibre-reinforced, sliding-modified
- Very high rigidity
- Very low coefficient of thermal expansion
- Friction and wear better than PEEK mod. otherwise similar mechanical properties
- High wear resistance up to 200°C
- Very aging-resistant, even in hot water and oil up to 170°C
- Very high resistance to gamma rays
Operational parameters
- Temperature (T):
–100 °C bis +190 °C (+200 °C) - Surface pressure (p):
max. 41 (125) MPa - Sliding speed (v)
max. 300 m/min - Fatigue (S)
tensile fatigue strength at 20 °C and and 106 stress cycles,
1 Hz = 59 MPa
Available as:
- plastic granules
- rods
- tubes
- sheets
- machined components
- injection moulded parts
- plain bearing bushes according to DIN
Examples of use
![ZX-410 Family 1 Railway jacks motion nut](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-6.jpg?fit=188%2C186&ssl=1)
![ZX-410 Family 2 Orthopedic toe alignment splint](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-11.jpg?fit=197%2C196&ssl=1)
![ZX-410 Family 3 Thrust bearings in oxygen valve](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-10.jpg?fit=115%2C192&ssl=1)
![ZX-410 Family 4 Components in commercial aircrafts water supply](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-9.jpg?fit=378%2C240&ssl=1)
![ZX-410 Family 5 Components in commercial aircrafts](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-8.jpg?fit=329%2C240&ssl=1)
![ZX-410 Family 6 Industrial machine and plant production](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-6.jpg?fit=188%2C186&ssl=1)
![ZX-410 Family 7 Seals in drill machine](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/07/CAT_Anwendungskatalog_2016_DE.pdf-Adobe-Acrobat-Pro-DC-1.jpg?fit=279%2C191&ssl=1)
![ZX-410 Family 8 Plain bearing bush in the hydraulic cylinder of a folding top](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/04/Cabrio.jpg?fit=510%2C382&ssl=1)
![ZX-410 Family 10 Spur gears in roll cutting and winding machines](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/04/KAMPFMAS.jpg?fit=510%2C304&ssl=1)
![ZX-410 Family 11 Ball joint bearings for systems in rolling mills](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/04/Fotolia_113467785_L.jpg?fit=510%2C341&ssl=1)
![ZX-410 Family 12 Wheel gear in horizontal transport devices](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/04/aetzanlage.jpg?fit=510%2C382&ssl=1)
![ZX-410 Family 13 Slideway in a surface grinding machine](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/04/3ü722.jpg?fit=443%2C382&ssl=1)
![ZX-410 Family 14 Slide bushes in hoist saws](https://i0.wp.com/www.zedex.de/wp-content/uploads/2020/04/BUEGEL_HUBSAEGE_02.jpg?fit=510%2C382&ssl=1)
![ZX-410 Family 15 Sliding blocks in concrete saws](https://i0.wp.com/www.zedex.de/wp-content/uploads/2019/10/IMG_1044_2-scaled-e1587128350573.jpg?fit=484%2C382&ssl=1)
Product shapes, processing methods
and finished parts
Product shapes
- Granules
- Rods
- Hollow rods
- Sheets
- 3D-Filament
- machined parts
- injection moulded parts
- 3D-printed parts
Processing methods
- CNC milling
- CNC lathe
- Conventional lathe
- CNC automatic lathe
- Grinding
- Threads
- Dressing – profiling
- Sawing
- Planing
- Roughening of adhesive surfaces
- Injection moulding
- Coating – cladding
- Labelling
- Bonding
- 3D printing
Finished parts
- Precision bushings
- Plain bearing bushes according to DIN
- Sliding guides
- Slideways
- Gears
- Track rollers
- Spindle nuts
- Seals
- Scrapers
- Gear racks
- Toothed belt discs
- Rudder bearings
- Pump bearings
Documentation
Application flyer
Technical data sheets
ZX-410 (TDS)
ZX-410VMT (TDS)
Certificates of conformity
ZX-410 (FDA)
ZX-410 (REACH)
ZX-410 (RoHS)
What is your challenge today?
Ask the right questions to let us develop the ideas to win it!
![ZX-410 Family 16 wolf kunststoff gleitlager gmbh logo](https://i0.wp.com/www.zedex.de/wp-content/uploads/2019/09/wolf-kunststoff-gleitlager-gmbh-logo.png?resize=197%2C72&ssl=1)